Benchwork and Track

Laying Model Railroad Track and Handlaying Your Own

A practical guide to laying model railroad track: preparing the surface, plywood vs foam, flex track, electrical basics, handlaying, and what it costs.

On this page
  1. Before you lay any track
  2. Plywood or foam under the track?
  3. Roadbed and fixing the track
  4. Flex track, sectional track and turnouts
  5. Electrical basics while laying
  6. Handlaying your own track
  7. Other meanings of building your own train track
  8. What does it cost?
  9. How full-size railroads lay track
  10. A note on pennies and coins

Before you lay any track

Track laying goes best when the benchwork is already solid, level and finished. If you are still deciding on the frame, start with model railroad benchwork. Then:

  1. Draw the plan at full size or close to it. Use paper or a printed plan on the surface, so you can see how curves and turnouts will fit.
  2. Mark the centerline. Draw the track centerline on the sub-roadbed with a pencil, using a flexible batten or a template for smooth curves.
  3. Test with unfastened track. Lay the track loosely and run your longest, stiffest equipment through it. Fix problems when it is still easy to move.
  4. Decide on grades and clearances. Check that tunnels, bridges and overhead structures clear your tallest rolling stock.

Plywood or foam under the track?

Either works, and the choice affects noise, weight and how you fasten the track. We weigh the two directly in plywood or foam for model railroad track.

  • Plywood is stiff, takes screws and nails well, and gives a stable surface. It can be noisy because it acts like a soundboard.
  • Extruded foam is light and quieter, and carves easily for terrain. It does not hold screws or spikes well by itself, so track is usually glued, or a thin wood or Homasote layer is added.

Many hobbyists combine the two, for example plywood or foam as the sub-roadbed and a resilient roadbed on top. One forum discussion described a layout with Homasote on plywood and foam roadbed on top, which the builder said reduced noise noticeably. The roadbed choice is covered in cork vs foam roadbed.

Roadbed and fixing the track

Roadbed raises the track slightly, provides a gentle shoulder for ballast, and can help with noise. Common fixing methods include:

  • Adhesive: white glue or latex caulk, spread thinly, with pins or weights to hold the track until it dries.
  • Track nails or small spikes: easy to remove and adjust, although it is easy to over-drive them and distort the track.
  • Screws: useful in some larger-scale track systems, where they go into a wood or Homasote layer rather than into foam.

Whichever you pick, avoid gluing the rail joiners and the ends of moving turnout parts. Keep adhesive out of the moving parts of the turnout and off the rail head.

Flex track, sectional track and turnouts

  • Sectional track comes in fixed lengths and curves. It is the easiest to install and well suited to starter layouts and temporary setups.
  • Flex track comes in long lengths that you bend and cut to suit your plan. It allows smoother, more realistic curves. Our guide to bending flex track into smooth curves covers the technique, including how to avoid kinks.
  • Turnouts (also called switches) are usually bought ready-made. Place them first, then connect the rest of the track to them. Proper alignment at the turnout ends reduces derailments.

Use gentle easements where straight track meets a curve, and avoid placing joints in the middle of a transition. If you can, use curves broader than the minimum your equipment can manage, since larger radii run more reliably and look better.

Electrical basics while laying

Plan the electrical side as you build rather than afterwards:

  • Power feeders: solder or connect feeder wires to the rails at regular intervals, rather than relying on rail joiners to carry current across the whole layout.
  • Soldered joiners: many modellers solder rail joiners on curves, which also helps hold the alignment.
  • Gaps and insulators: only add them where your wiring design needs them.
  • Test continuously. Run a locomotive over each new section before moving on.

Metal objects across the rails can cause short circuits, which is one reason to keep tools and loose hardware away from powered track.

Handlaying your own track

Handlaying means building the track from individual ties and rail rather than using ready-made flex track. Many modellers do it for realistic detail, custom turnouts and a better fit for unusual trackwork.

The general method is:

  1. Lay out the ties. Glue wood ties (or use ready-made tie strips) to the roadbed, using a spacing template or jig for even spacing.
  2. Position the rail. Slip rail into place on the ties and hold it with small spikes, or secure it with adhesive, depending on your tie material.
  3. Gauge the track. Use a track gauge frequently to keep the rails the correct distance apart.
  4. Join sections carefully. Rail joiners or soldering keep alignment and electrical continuity.

Handlaying takes more time than snapping together ready-made track, so many beginners start with flex track and add handlaid sections later, such as turnouts or industrial spurs.

Other meanings of building your own train track

Searches for “build your own train track” cover several different projects:

  • Wooden toy track for children, cut from hardwood with matching connectors.
  • Wall-mounted decorative track made of painted slats and rope or similar materials.
  • Model railroad track in HO, N, O or other scales, as described above.
  • Backyard and ride-on railways, which involve full structural engineering and are outside the scope of this guide.

Pick the one that matches your goal, since materials and methods differ widely.

What does it cost?

Costs vary by scale, brand, region and how much ready-made track you buy, so we will not quote exact prices. The main cost factors are:

  • Track type: sectional, flex, handlaid, and code (rail height).
  • Number and type of turnouts, which are often the most expensive items per piece.
  • Roadbed, glue, nails and ballast.
  • Electrical parts: feeders, a controller, and connectors.
  • Tools, such as a track gauge and rail nippers.

How full-size railroads lay track

Prototype railroads lay track on prepared ground with a layer of crushed stone ballast. Ties are placed on the ballast, rails are fastened to the ties, and machines then align and tamp the track. Modern work uses specialized equipment and trained crews. Your model follows the same logic at a much smaller scale.

A note on pennies and coins

A common question is what happens when you put a penny on a railroad track. Placing anything on real railroad tracks is dangerous and illegal trespassing in many places, so we do not recommend it. On a model railroad, coins and other metal objects can cause shorts across the rails, so keep them clear of powered track.

The complete guide to benchwork and track

Model Railroad Benchwork and Platform Construction
Read the guide

Keep exploring

Guides from other topics

All topics →