Wiring and DCC

Turnouts and Point Motors for Model Railways

A practical guide to turnouts and point motors for model railways: twin-coil, stall and servo types, the switches that control them, frog wiring and common mistakes.

On this page
  1. Turnouts, points and switches: the terminology
  2. Ways to throw a turnout
  3. Types of point motors
  4. Switches that operate point motors
  5. Frog polarity and wiring
  6. CDUs and DCC accessory decoders
  7. Indicators and signals
  8. Mistakes to avoid

Turnouts, points and switches: the terminology

A turnout is the track component that lets a train go one of two ways. In British usage it is called a set of points, and the moving rails are the point blades. In North America the same thing is often called a switch, which causes confusion because “switch” also means an electrical toggle. This article calls the track part a turnout, and the electrical part a switch.

Searching for “point switches” usually means one of two things: the switch you use to operate a point, or the motor that moves it. Both are covered below.

Ways to throw a turnout

  • By hand: a lever, a ground throw or a finger on the points. It costs almost nothing and is reliable, but you have to reach the turnout.
  • By a spring or non-derail design: some turnouts are spring-loaded so a train pushes the points over from the trailing direction.
  • By a motor: a point motor moves the blades from a control panel, a handheld throttle or a computer, and is used when turnouts are out of reach or when you want automatic operation.

Many modelers throw yard turnouts by hand and power the ones on the main line that are hard to reach.

Types of point motors

Twin-coil (solenoid) motors. Two coils pull a plunger in one direction or the other with a brief pulse. They are fast and often built into the turnout, and they are common on snap-style track. The coils are intended for short pulses only; holding the button down can overheat and burn them out. They are usually driven by a momentary push-button or switch, often through a capacitor discharge unit (CDU), which stores up a pulse of power so the coils get a quick, firm kick.

Slow-motion (stall) motors. These use a small motor that moves the points slowly and then “stalls” against its end stop, holding the points with gentle continuous pressure. Tortoise-style machines are the best-known example. The slow motion looks realistic and the points are held firmly, but they are mounted under the baseboard, so you need to plan clearance and a hole in the base. Continuous power is normal for these.

Servo motors. A small hobby servo moves the points through a wire, usually controlled by a dedicated servo controller or decoder. They are cheap and slow-moving, but they need some set-up, such as adjusting the end positions.

Whichever you choose, check the manufacturer’s specifications, since voltage and polarity requirements vary.

Switches that operate point motors

  • Momentary push-buttons or center-off toggles suit twin-coil motors, because they only give a short pulse.
  • Latching toggle switches suit stall motors, because they hold a polarity.
  • A DPDT switch (double-pole, double-throw) can reverse the polarity for stall motors and can switch frog polarity or panel indicator lights at the same time.

Mount the switches on a control panel with a simple track diagram, so the position of each switch makes sense at a glance. Some builders add a small LED to show the route that is set.

Frog polarity and wiring

The frog is the V-shaped part where the two rails cross inside a turnout. On a turnout with a live (power-routing) frog, the frog polarity depends on which way the points are thrown, and trains can stall or short if the frog gets the wrong polarity. On an insulated frog turnout, the frog is electrically dead and the rails supply power through the point blades.

Many turnouts that are described as “electrofrog” or “power-routing” need the frog to be switched to match the route. Some do this through the points themselves and some need a switch or relay, often in the same motor that moves the points. Check the instructions for your brand. If you are using DCC, wiring the frog correctly also helps prevent short circuits, since a metal wheel can bridge the gap at the frog.

Run feeders to the rails on either side of each turnout, in addition to relying on the rail joiners, to keep power reliable. See DCC track feeders for placement ideas.

CDUs and DCC accessory decoders

A capacitor discharge unit (CDU) stores energy and releases it in a short burst. It helps twin-coil motors work reliably and protects them from being held on too long.

On a DCC layout, an accessory decoder can throw points from the same handheld throttle you use for trains, and many types also support automatic route setting. You still need to match the decoder to your motor type: twin-coil, stall and servo motors all need different outputs.

Indicators and signals

Small dwarf signals or LEDs can show which way a turnout is set. Kits are made for twin-coil, stall-motor and bipolar two-wire switch types, so choose one that matches your motor. For more on signal options see model railroad signals for HO and G scale.

Mistakes to avoid

  • Holding a button down on a twin-coil motor.
  • Mounting a stall motor without enough clearance or alignment, so the points don’t move fully.
  • Powering accessories from the track bus. A separate accessory supply avoids interference with the track signal.
  • Forgetting that turnouts at reverse loops and wyes affect your gaps and polarity. See reverse loops and wyes.
  • Gluing down track before testing the turnouts and motors.

For the overall wiring plan, see the model train track wiring guide.

The complete guide to wiring and dcc

Model Train Track Wiring: A Complete Guide
Read the guide

Keep exploring

Guides from other topics

All topics →