Why kinks happen
A kink is a sharp, localized bend in the rail instead of a gentle, even arc. It usually appears when track is pushed into a curve from one end, when a rail joiner sits right at the point where the curve begins, or when track is bent past what the rail wants to do easily. Kinks cause derailments and rough running, particularly with long locomotives and cars.
Before you bend
- Choose a radius that suits your equipment. Wider curves run more reliably. Don’t go tighter than the minimum recommended for your locomotives and cars; our guides to HO minimum curve radius and N scale minimum radius give typical figures.
- Mark the centerline. Draw the curve on the roadbed or sub-roadbed with a pencil, using a template, a flexible batten, or a compass-like trammel.
- Lay the roadbed first. See cork vs foam roadbed if you are still deciding.
- Gather tools. A track gauge, rail nippers or a cutoff disc, files, pins or small track nails, and solder or rail joiners.
Step by step
- Pre-curve the track by hand. Gently flex the track along its length before you place it, so it is used to the shape.
- Fix the starting point. Pin or fasten one end, aligned with the track before the curve.
- Bend and mark the far end. One experienced forum poster suggested not working from one end to the other, but fixing the start, bending the track, then marking and cutting the far end. In many cases the center of the curve then forms a natural, smooth arc.
- Hold the middle. Use pins or weights, then check the curve against your centerline.
- Fasten gradually. Work from the center outward, or in short stretches, checking the curve as you go.
- Check with a gauge and a long car. Roll a long piece of rolling stock through to find any dips or tight spots.
Which side does the sliding rail go on?
Many flex track products have one rail that slides in the ties so the rails can move relative to each other as the curve forms. With Atlas-style flex, forum modellers generally place the sliding rail on the inside of the curve. Their reasoning was that the inside rail is the shorter one, and that the inside tie ends squeeze together, whereas putting it on the outside would spread the tie ends beyond what looks realistic. Some brands, such as Peco, let both rails slide. Follow the manufacturer’s instructions for your product.
Joiners and the kink
The most common place for a kink is at a rail joiner, because the rail is stiffest at the joint. Some ways to avoid it:
- Do not put a joint at the very start of the curve. Move the joint to a straight section or well into the curve.
- Let the rail ends overlap and trim after curving. When you bend the track, the rail on the outside or inside of the curve will extend past the ends of the ties. Cut the rail after the curve is shaped, rather than before.
- Solder joiners after the curve is placed, not before, so the soldered joint does not set a straight spot.
- Pre-curve rail ends, so the end that enters the joiner already has a curve built in. Some modellers use a rail-forming tool, sometimes called a roller, for this.
Tools and tricks
- Templates: a curve cut from a sheet of thin MDF or plywood, at the radius you want, can be used to shape the track before you fix it.
- Track gauge: one forum modeller recommended using a gauge to “comb” the track through curves, correcting tie spacing and rail position.
- Push pins and small nails: enough to hold the track without bending it.
- Easements: a gradual transition between a straight and a curve. Start the curve gently and increase the bend slowly. Avoid sharp transitions.
Stiff versus flexible brands
Brands behave differently. Forum members reported that some flex track, such as certain Micro Engineering products, keeps its shape once bent and does not spring back, which makes it easy to adjust but can make it hard to produce an evenly symmetrical curve. Others, such as Atlas, were described as easier to form into flowing curves but needing more pinning to stay in place. Peco was mentioned as a middle option. Opinions varied widely, so one useful approach is to buy a short length of the brand you are considering and test it before ordering a lot.
Troubleshooting
- Flat spots or a wave in the curve: unfasten the section, re-form it, and check against the centerline.
- Ties bunching or spreading: adjust the tie spacing with a gauge or by hand.
- Gaps at the joiners: slide the rails back into the joiner and recheck alignment.
- Persistent kink: cut out the section and replace it, or adjust the joint position.
For the broader process, including turnouts and electrical connections, see laying model railroad track. If you are laying curves in a spiral, the helix guide covers the extra points to check.