Wiring and DCC

Is it best to lay model railroad track on plywood or foam?

Plywood or foam for model railroad track? Compare weight, cost, noise, scenery and wiring, and see when each base or a combination of both works best.

On this page
  1. Quick answer
  2. Plywood: strengths and weaknesses
  3. Foam: strengths and weaknesses
  4. Combining the two
  5. Roadbed and track fixing
  6. Wiring through plywood and foam
  7. Which to choose

Quick answer

Neither is universally best. Plywood is the traditional, strong and forgiving base, and foam board is lighter, quieter and easier to shape for scenery. Many modelers use both: plywood or a frame for structure and foam on top for the scenery and track base. Choose based on your benchwork, budget, tools and how much landscaping you plan.

Plywood: strengths and weaknesses

Strengths

  • Strong and holds screws and nails well, so track, switch machines and other hardware can be fixed down easily.
  • Familiar and widely used with open-grid and L-girder benchwork.
  • Works with a wide range of adhesives and fasteners.

Weaknesses

  • Heavier than foam, which matters if the layout needs to be moved.
  • Can transmit train noise, since it acts like a sounding board.
  • Can warp if it gets damp or is poorly supported.
  • Carving hills and valleys requires a separate layer of scenery material.

Foam: strengths and weaknesses

Foam here usually means extruded foam insulation board in sheets, commonly 1 to 2 inches thick.

Strengths

  • Light, which makes it good for portable layouts and for builders who struggle to lift plywood.
  • Easy to cut and carve with simple tools, so you can shape terrain, rivers and roadbed.
  • Quieter than a bare plywood top.
  • Wire holes can be cut with a tool or even pushed through.

Weaknesses

  • Needs good support underneath, or it can sag.
  • Some solvents and adhesives dissolve foam, so use products labelled as foam-safe.
  • Does not hold nails or screws as strongly, so heavy items such as switch machines may need a mounting block.
  • Cutting foam creates dust and sometimes fumes from hot-wire tools, so work with good ventilation.
  • Foam can be damaged by a soldering iron if you are not careful.

Combining the two

A common approach is to build open-grid benchwork, add a plywood subroof where the track runs, and use foam on top or alongside for scenery. Others use foam on top of a plywood table so they can carve below track level for rivers and cuttings.

Roadbed and track fixing

Cork roadbed is a common choice on both, and foam roadbed is also sold. Track can be glued with white or latex-based adhesives, caulk or other products suited to the base, or fixed with small nails on plywood. Always test an adhesive on a scrap of foam before you use it on the layout.

Do not glue track down until you have checked electrical continuity and your feeder locations, because track is much easier to fix before it is permanent.

Wiring through plywood and foam

This is where the wiring-control choices matter:

  • Plywood: drill holes for feeders and mount terminal blocks, bus wires and switch machines underneath. The wood handles screws and staples.
  • Foam: feeders pass through easily, but support anything heavy with wood. Keep soldering well away from the surface, and do not leave a hot iron on or near the foam.
  • Both: drill or cut feeder holes before you lay the track, and label the wires so you can trace them. Work out where your feeders go with DCC track feeders: how many you need and where to put them and size your bus with what wire gauge to use.

Point motors that mount under the baseboard need a hole and a way to be fixed. See turnouts and point motors for model railways.

Which to choose

  • Choose plywood if you want a strong, conventional base and are comfortable with carpentry.
  • Choose foam if weight, noise and easy terrain shaping matter most.
  • Choose both if you want strong benchwork with scenic flexibility.

For the full picture of how wiring fits into the build, see the model train track wiring guide.

The complete guide to wiring and dcc

Model Train Track Wiring: A Complete Guide
Read the guide

Keep exploring

Guides from other topics

All topics →