Ready-made or build your own?
Tunnels are one of the most satisfying scenic features on a model railroad. They let trains disappear and reappear, they can hide a sharp curve or a staging area, and they add drama to a hillside. For HO scale there are two broad routes.
Ready-made or pre-formed tunnels. Manufacturers such as Woodland Scenics sell pre-landscaped tunnel sections (straight and curved), and various makers offer double-track versions, some of them 3D-printed. These are quick to install and suit small layouts or first projects. The trade-off is size and shape: a ready-made unit has a fixed length, curve and width, so check that it fits your track radius and spacing before you buy.
Building your own. A scratchbuilt mountain lets you choose the length, shape and position, and blend it into the rest of your terrain. It takes longer, but it is often the better choice for custom track plans, double-track mainlines or large hillsides.
Either way, the tunnel is only as good as the portal and the scenery around it.
Plan before you build
Tunnels are harder to modify after the mountain has been built, so settle these points first.
Clearance
Make sure the opening is tall and wide enough for the tallest and widest equipment you run, with some margin. Check with your biggest locomotives and cars, including any with tall roof details, and any that overhang on curves. Test on the curve itself, since long cars swing out from the track centre line.
Curves and length
A tunnel placed on a curve needs more width, not less. If the tunnel is on a curve, make sure the portal and interior allow for the overhang of long rolling stock. A tunnel that is a bit longer than your longest train hides the whole train briefly, which is a nice effect. A very short tunnel can show the entire train through the portals.
Access
Derailments and stalled trains happen. Always plan some way to reach the track inside the tunnel, such as:
- A lift-off mountain that is not glued down.
- A hatch or removable section in the hillside or at the rear of the layout.
- Reach-in access from below or behind, where practical.
Do not rely on your hand fitting through the portal. It rarely does.
Keep the track inside clean and well laid, as a problem there is the hardest to fix. Many modellers also add basic wiring and a way to see inside, such as a small light.
Choosing portals
The portal is the framed opening at the tunnel mouth. It is what most people see, so it should suit your era and region.
- Cut-stone, concrete or timber portals are available as cast plaster, resin or plastic pieces from makers such as Woodland Scenics and Bachmann.
- Timber portals suit narrow-gauge, logging and early railroads, and are easy to scratchbuild from stripwood.
- Single vs. double. Double-track portals are wider and may need custom building or a specific double-wide model.
Weather the portal after installing it, so the stone or concrete looks aged and soot-stained. See how to weather model railroad buildings and structures, as many of the same stains and washes work on portals.
Building a tunnel mountain
A common approach:
- Lay and test the track first. Run trains through, then ballast and check again.
- Install the portal at the tunnel mouth, with the opening square to the track.
- Build the mountain shell over the track using foam, cardboard lattice or wire mesh, keeping it removable if you can. Brace it so the roof does not sag onto the track.
- Cover and shape with plaster cloth or similar, then add rock faces. A good way to add interest near the portal is with cast plaster rock faces.
- Paint and add ground cover, then plant trees on the slopes, working down to the portal. The DIY scenery guide covers these steps in more detail.
Liner forms, which are moulds for casting interior rock walls with plaster, are available if you want the inside near the portal to look finished.
Finishing the inside
Most viewers only see the first few inches inside, so concentrate your effort there. Paint the interior, including the ceiling and the sides, a flat black or dark grey, to stop the tunnel from looking like a cardboard tube. Extend rock or liner texture beyond the portal edge to avoid a flat, painted look.
Keep the interior free of loose debris and glue spatter, and make sure nothing hangs low enough to catch a pantograph, brake hose or roof detail.
Common tunnel problems
- Tunnel too narrow or too low for larger equipment.
- No access, so a derailment means taking the layout apart.
- Portal not square to the track, giving a skewed look.
- Light-coloured interior visible through the opening.
- Obvious “box” shape. Soften it with slopes, rock faces, trees and ground cover.