Wiring and DCC

Model Railroad Signals for HO and G Scale

A guide to model railroad signals for HO and G scale: block, dwarf and crossing signals, how LED signals are powered and controlled, and outdoor G scale options.

On this page
  1. What signals do on a model railroad
  2. Types of HO signals
  3. How HO signals are powered and controlled
  4. Wiring basics: LEDs and resistors
  5. G scale signals
  6. Why G scale trains cost more, and who makes them
  7. What railroad signals and signs mean
  8. Planning signals on your layout

What signals do on a model railroad

On a real railroad, signals tell crews whether the track ahead is clear. On a model railroad they do two jobs: they add realism, and, if you wire them to track detection, they can actually show whether a block is occupied or which way a turnout is set. Many layouts only use signals as scenery, and that is a perfectly good choice.

Signals range from simple non-working models to fully automated LED systems tied to detectors.

Types of HO signals

HO (1:87) offers the widest selection. The main types are:

  • Block signals: mast or cantilever signals showing red, yellow or green to indicate whether a block of track is occupied. They are available as non-working models and as working LED versions.
  • Searchlight and prototype-style signals: single- or multi-head signals modeled on particular real-world systems, with modular systems and control boards offered by several makers.
  • Grade-crossing signals: flashing crossbucks, cantilever flashers and wigwags that animate road crossings, usually with a controller that senses the train.
  • Dwarf and position-light signals: low signals used in yards and at turnouts, along with regional types like color-position-light signals that suit particular railroads and eras.

Makers frequently mentioned include Atlas, Walthers, Azatrax, Showcase Miniatures, Midwest Model Railroad and Custom Signal Systems. Check each product’s listing for compatibility with your scale and control system.

How HO signals are powered and controlled

Working signals can be controlled in several ways:

  • Manually, with toggle switches on a control panel.
  • Automatically, with infrared sensors or occupancy detectors that sense a train in a block.
  • Through DCC, using signal decoders and control boards.
  • Linked to a turnout, using a dwarf signal kit that matches your point motor. Kits are sold for twin-coil, stall-motor and bipolar two-wire turnout machines. See turnouts and point motors for model railways to identify yours.

Wiring basics: LEDs and resistors

Most working signals use LEDs. LEDs need a current-limiting resistor in series, or they will burn out. Many products include the resistors or are designed for a specific voltage, commonly in the range of roughly 12 to 16 volts, but this varies, so follow the instructions supplied. If you are building your own, resistor values are calculated from your supply voltage and the LED’s rating.

It is usually best to power signals from a separate accessory supply instead of the track bus, so they don’t load or interfere with track power. The basics of bus wiring are in the model train track wiring guide.

If you want signals to react to trains, you will need a form of detection. Options include current-sensing detectors, infrared sensors and isolated track sections feeding a detection circuit. The simplest signals just follow a switch.

G scale signals

G scale is the large scale most often used for garden railways. G gauge track is 45 mm between the rails, and the scale ratios vary by manufacturer. Because G scale is used outdoors, signals need to be weather-resistant, and many people use crossing signs, lights and lineside details more than full signal systems.

Dedicated G scale signal options are fewer than for HO. Modelers commonly:

  • buy or kit-build signals designed for large scale;
  • convert or scratch-build signals with LEDs; and
  • control them with simple switches, relays or small controllers.

Wire used outdoors should be rated for the environment, with connections protected from moisture. If you run a garden line, plan for ground movement and weather when choosing signal locations.

Why G scale trains cost more, and who makes them

Large models use more material and often have more detail, bigger motors and more complex mechanisms, so they generally cost more than smaller scales. As for the “best” brand, the answer depends on your budget and your interests, and several manufacturers are well regarded. Read recent reviews and ask in garden-railway forums before buying.

What railroad signals and signs mean

On real railroads, signals are indicators of track conditions, and the rules differ by country and railroad. As a general idea, red means stop, yellow means proceed with caution or be prepared to stop, and green means proceed. Signs along the track, such as mile posts and speed limits, are separate from signals. If you want accuracy, choose the railroad and era you model and look up the signal rules for it.

Planning signals on your layout

  1. Decide whether signals will be scenery or functional.
  2. If functional, plan your detection first, because the signals are driven by it.
  3. Choose a power supply for accessories.
  4. Place signals so they are visible and match the railroad’s practice.
  5. Test everything before the scenery goes in.

The complete guide to wiring and dcc

Model Train Track Wiring: A Complete Guide
Read the guide

Keep exploring

Guides from other topics

All topics →