Quick answer
A common choice is 12 to 14 AWG wire for the bus (the main wire pair under the layout) and a thinner wire, often 18 to 22 AWG, for short feeders that connect the bus to the rails. Use 12 AWG for a larger layout or long runs, and 14 AWG is widely considered enough for many home layouts. Always use pure copper wire, and keep feeders as short as practical.
These are rules of thumb that many modelers follow, not hard limits. Scale, layout size and number of locomotives all matter.
Wire gauge basics
AWG (American Wire Gauge) numbers run backwards: a lower number is a thicker wire. 12 AWG is thicker than 14 AWG, which is thicker than 18 AWG, which is thicker than 22 AWG.
A thicker wire has lower resistance and can carry more current with less loss. It also costs more and is harder to bend and terminate.
Why voltage drop matters
Every wire has a small resistance. When current flows, some voltage is lost along the way, and the farther it goes and the thinner the wire, the more is lost. On a model railroad, the voltage is low, so even a volt or two of loss can be noticeable: locomotives slow down far from the power source or run differently in different areas. On DCC, too little voltage can also affect how reliably decoders read the signal.
Wire sizing is mostly about keeping that loss small. It is current, not voltage, that determines how thick the wire needs to be, and distance determines how much loss you get.
Typical sizes
These are common approaches, not guarantees:
| Part | Typical choice | Notes |
|---|---|---|
| Bus (main wire pair) | 12 to 14 AWG | 12 AWG for large or long layouts |
| Feeders (bus to rail) | 18 to 22 AWG | Keep them short; thicker is easier to carry current, thinner is easier to solder |
| Wiring from a power supply to the bus | Same as bus or thicker | This section carries the total current |
| Accessory wiring | Often 18 to 22 AWG | Depends on the load |
Some builders use 14 AWG for the bus and 18 AWG for feeders on O gauge layouts, and 12 AWG for the bus if they have the budget. Others keep feeders under about 3 feet, since a long thin feeder is where voltage is most easily lost. In small scales like N, thinner wire is often adequate because the current is lower, though many still use a 14 AWG bus for simplicity.
If you want to calculate rather than guess, use an online voltage-drop calculator with your actual wire length and expected current, and choose a conservative allowable drop.
Why household wire charts mislead
Charts that say a certain gauge can carry a certain number of amps are built for 120-volt building wiring, where the allowable voltage drop is a few percent of a much larger voltage and the wire length is long. A track circuit is low voltage, so the same absolute drop is a much bigger problem. Use those charts for safety limits only, not for deciding layout bus size.
One forum builder pointed out that wire size depends on the amperage you expect to carry, not the voltage, and recommended basing your choice on gauges that have worked on other layouts.
Bus, feeders and home runs
- The bus carries current over a distance. Its ends can simply stop; they do not need to loop back or connect to anything.
- Feeders are short wires from the bus to the track. Current flows through whichever feeders are nearest to the locomotives drawing it, so voltage is not divided among them.
- Some modelers prefer home-run (star) wiring, with a separate pair from a central point to each section. It uses more wire but can give very low voltage drop and easier fault finding.
For how many feeders you need, see DCC track feeders: how many you need and where to put them.
Copper vs copper-clad aluminum, solid vs stranded
Check what the wire is made of. Some inexpensive speaker or “audio” wire is copper-clad aluminum (CCA), which has higher resistance than pure copper. One builder estimated that a CCA wire sold as 12 AWG performs more like a thinner copper wire. A low price per foot can be a clue. Buy pure copper, and if the product page doesn’t say, assume it might not be.
Stranded wire is more flexible and easier to run and route under a layout. Solid wire is stiffer and can be easier to push into some connectors or poke through baseboards. Either works if the connections are secure.
Twisting the bus for DCC
Many DCC modelers twist the two bus wires together along their run. This helps reduce interference with the digital signal. A simple way is to clamp one end in a drill and spin the other, then run the twisted pair under the layout.
Check your work with a meter
After you wire the layout, measure the voltage at the power connection and at a rail far from it while a locomotive is running. A significant difference means there is a problem: a poor joint, a long thin feeder or a bus that is too small. Fix it by adding feeders, shortening or thickening feeders, or using a heavier bus.
For the overall plan, see the model train track wiring guide and how to power a DCC track.