Layout Planning

Planning Your Model Railroad: Track Plan Design from Scratch

How to plan a model railroad from a blank room: set goals, measure space, choose a layout shape, design the track plan and test it before laying any track.

On this page
  1. Start with goals, not track
  2. Measure the space and choose a scale
  3. Pick a theme, era and place
  4. Common layout shapes
  5. Track plan design basics
  6. Operations: what the trains will do
  7. Drawing the plan
  8. Where to find free track plans
  9. Test before you build
  10. Common planning mistakes

Start with goals, not track

The most useful planning question is not “which track plan should I copy?” but “what do I want to do with this railroad?” Some people want trains running continuously while they watch. Others want to switch freight cars, build detailed scenery, or run a long passenger train through a convincing landscape. Each goal pushes the design in a different direction.

Write down three or four priorities before you draw anything. Typical ones include:

  • Continuous running versus operating a “job” with a start and an end
  • Realistic operations (switching, timetables) versus scenery and display
  • Solo use versus inviting friends to operate with you
  • Long trains and broad curves versus lots of detail in a small area

A layout that tries to do everything in a small room usually does none of it well. Choosing what to leave out is part of good design.

Measure the space and choose a scale

Measure the room carefully, including doors, windows, heating vents, support posts and anything you cannot move. Note ceiling height if you plan a second level. Then decide how much of that space can realistically be given to the railroad while leaving room to get in and work on it.

Scale and space are linked. Smaller scales fit more railroad into the same room, because curves and turnouts take up less space. HO is the most common choice in North America, with N a popular option for smaller rooms and longer runs (see HO vs N scale for a side-by-side comparison). If you are unsure how much room each scale needs, see how much space you need for a model train layout. To get a feel for the size of N scale equipment, read what size an N scale train is.

Pick a theme, era and place

A theme gives you rules for what belongs on the layout, which makes a lot of decisions easier. It can be a real railroad, a real location, or an imagined one based on real practice. Era matters too, because it determines locomotives, rolling stock, vehicles and buildings.

Some modelers pick a prototype railroad and follow it closely. Others use a “freelanced” railroad that borrows from several real ones. If you want to model a specific company, our article on modeling a prototype railroad covers Pennsylvania Railroad, Southern Pacific and Amtrak themes.

Common layout shapes

Most home layouts are variations on a few basic shapes.

  • Oval or loop: Trains circulate continuously. It is simple and good for watching trains, but a basic oval has little operating interest on its own. See point-to-point versus loop layouts for how the two approaches compare.
  • L-shaped: Fits along two walls of a room and often leaves a large open area. It gives long runs with reasonable access.
  • U-shaped: Runs along three walls, leaving a central aisle or “operator pit”. U-shaped model train layouts make good use of a spare room because you can stand in the middle and reach most of the railroad. The trade-off is that the corners need careful design, and reaching the far corners from the aisle can be awkward if the benchwork is deep.
  • Shelf or around-the-walls: Narrow benchwork against the walls, often 12 to 24 inches deep. This keeps the centre of the room free. See how to design a shelf or around-the-walls model railroad.
  • Switching layout: A small layout built around moving cars between industries rather than running laps. See switching layout plans and car cards.

If space is very tight, look at compact layouts for small spaces.

Track plan design basics

Several rules of thumb apply regardless of the layout shape.

Curves. Wider curves look better and run more reliably. Very sharp curves can cause derailments, especially with long locomotives and passenger cars. Decide on a minimum radius for your equipment before you draw the plan; see minimum curve radius for HO scale.

Turnouts. The number of a turnout (for example, a #4, #6 or #8) describes how gradual its diverging route is. Higher numbers are longer and look and run better, but take more space. Many modelers use larger turnouts on main routes and tighter ones in yards and industrial areas.

Grades. If the layout has more than one level, keep grades modest. A steep climb limits train length and can stall locomotives. Work out the rise and the length available before committing.

Reach. Any point you need to reach for cleaning, repairs or rerailing should be within comfortable arm’s length. Be especially careful with tracks hidden behind scenery, in tunnels or in corners.

Clearances and aisles. Leave enough aisle width to move comfortably, and allow vertical clearance for bridges and overpasses with the tallest equipment you plan to run.

Hidden track. Hidden storage or staging can greatly increase operating interest. See fiddle yards and hidden staging and yard design in HO, N and O scale.

Operations: what the trains will do

Even a casual layout benefits from some thought about operations. Ask where trains come from, where they go, and what they do on the way. Industries that receive and ship cars give trains a reason to stop. Staging tracks let trains “arrive” from and “depart” to the outside world. A simple car routing system can generate varied work with a small amount of track; our article on switching layouts and car cards explains how.

Drawing the plan

Start with rough pencil sketches on graph paper at a known scale, or use paper cutouts of track sections. Once you have an idea you like, many modelers move to computer track-planning software such as AnyRail or SCARM, which include libraries of track from many manufacturers and flag connections that do not fit. Software is not required, and plenty of good layouts began as a sketch on paper.

Where to find free track plans

Many manufacturers, hobby magazines and layout-design websites publish plans, and some software gallery pages let you download plans others have shared. Free plans are a useful source of ideas, but treat them as starting points. Check that a plan suits your room, your scale and the radius and turnout size you want. For sources and tips, see where to find free model railway layout plans.

Test before you build

Before cutting benchwork, test the design in the real room:

  • Lay paper or cardboard templates of the track on the floor or a table
  • Lay out full-size sections of flex track or sectional track temporarily
  • Run the longest train you plan to operate around the curves
  • Check reach from the aisles and clearances at doors and windows

Changes at this stage cost almost nothing. After the track is laid and wired, they cost a lot.

Common planning mistakes

  • Designing for the space you wish you had rather than the space you do
  • Using curves that are too tight for the equipment you want to run
  • Packing in too much track, leaving no room for scenery or industries
  • Hiding track that cannot be reached
  • Building a very large layout before finishing a small one

A smaller layout that gets finished teaches you far more than a large one that stalls. Plan for what you can complete, and leave room to expand later if you want to.

Keep exploring

Guides from other topics

All topics →