Why weather structures
Weathering is usually discussed for locomotives and freight cars, but buildings benefit just as much. Right out of the box, most kits look new, with uniform colour and sharp edges. Real buildings fade, stain, rust and peel. Adding that wear can turn an ordinary kit into the most noticed part of a scene.
Weathering also comes in different levels. An abandoned depot can look heavily weathered, while a well-kept office may need only a touch of dust and soot. Decide on the story of the building before you start.
Plan the weathering
Look at photographs of real buildings of the kind you are modelling. Notice where grime gathers and where it does not:
- Bottom of walls: dirt splashed up from the ground, and often damp staining.
- Under windowsills, eaves and roof edges: streaks where rainwater runs.
- Around chimneys and vents: soot and rust.
- Sun-facing walls: paint tends to fade and peel.
- Corners and edges: wear and chipped paint.
- Roofs: often the most visible part of a building, with patchy shingles, rust and stains.
Work in light stages. It is easier to add more than to take away.
Materials
You do not need much to begin:
- Acrylic paints, flat finish
- Wood stains, or homemade stain (see below)
- Soft brushes of several sizes
- A stiff brush or cheap flat brush for drybrushing
- Weathering powders or artist’s chalks
- Isopropyl alcohol
- Paper towels
- A matte clear coat to seal, optional
- A fine pen or pencil for cracks and details
Isopropyl alcohol and spray finishes should be used in a ventilated area, away from flame, and following the labels.
Weathering wood
Wood buildings offer the most scope for realistic weathering.
Stains and washes
A common way to create a grey, aged wood look is with thin stains:
- Commercial stains. Several companies sell factory-mixed stains for model use, in a range of colours.
- Homemade wash. One approach is a mix of India ink and 70 percent isopropyl alcohol; the more ink, the darker the stain. Sepia ink gives a warmer tone. Acrylic paint can be substituted for ink. Adjust the strength on spare wood first.
Brush the wash along the grain, using up the stain in the brush before reloading, as this creates natural variety between boards. Different woods take stain differently, and you may need a second coat on some pieces.
Preventing warping
A water-based wash, or an alcohol mix that contains water, can warp thin wood. Lay stained pieces flat to dry, covering them with paper towels and a weight such as books, and give them time to dry fully. Bracing walls from the inside with strip wood helps prevent warping and sagging later. Do not apply alcohol-based washes after you have attached peel-and-stick trim or other parts, as they can affect the adhesive.
Peeling and worn paint
To mimic paint that has aged and flaked:
- Stain the bare wood first.
- Paint the walls in the building colour. A light coat is better than a thick one.
- Once the paint is dry, scrape or abrade it to expose wood beneath. Tools designed for this, such as distressing brushes, work well, but a stiff brush, a sanding stick or a fine abrasive pad can also do the job.
- Smooth any fuzz with a fine finishing pad.
- Apply a final thin wash to tone down bare areas and tie the colours together.
Concentrate wear on lower walls, corners, doors and sun-exposed sides.
Weathering brick, concrete and plastic
- Brick. Wash the whole wall with thin, dark grey or brown paint and wipe the surface with a cloth or paper towel so that the colour remains in the mortar lines. Lightly drybrush a lighter colour over raised brick. Add soot above chimneys and windows, and streaks below sills.
- Concrete. Concrete often darkens with grime and stains from water. Use thin grey and brown washes, with darker streaks below ledges and at the base.
- Plastic. Plastic kits usually have a moulded sheen. A matte clear coat or flat paint reduces it. Washes of thinned paint settle into moulded detail such as siding grooves and brick joints.
- Metal and corrugated siding. Add rust with dull orange and brown paints or powders, particularly at the bottom edges, around fasteners and along seams. Use rust sparingly.
Roofs
Many roofs are seen from above on a layout, so they deserve attention.
- Shingle roofs. Vary individual shingles with slightly different shades of grey or brown. Leave a few missing, or patch them with a different colour for a repaired look.
- Drybrush highlights. Load a brush with a light grey, wipe almost all of it off, and brush lightly across the roof to catch the raised edges.
- Soot and stains. Use powders or very thin paint around chimneys, vents and under overhangs.
- Flat roofs. Use dark and light patches, tar streaks and dust.
- Rooftop details. Vents, water tanks, antennas and signs break up bare roofs.
Windows and glass
Dirty windows read as real, and clear plastic windows can be dulled with a light coat of flat clear finish or a thin wash applied to the inside surface. Keep some transparency, so the effect looks like dust and not frosting. Broken panes can be shown by cutting away part of a window or scribing cracks with a knife blade. Curtains, shades and interior details add depth.
Drybrushing and powders
Drybrushing highlights texture. Dip the tip of a brush, wipe off most of the paint on a paper towel, then lightly drag it over the surface. Only the raised edges pick up colour. It works on wood grain, brick, roof shingles and stone.
Weathering powders (artist’s chalks or commercial pigments) are good for dust, soot, rust and dirt. Apply with a soft brush and build up gradually. Powders can be fixed with a light matte spray, but test it first because it can change colours.
Seal and protect
A thin coat of matte clear finish can protect weathering from handling. Apply lightly in thin coats, in a ventilated space, and test on a spare piece. Glossy finishes are rarely used on weathered buildings, and some products can make washes shift or cloud.
Common mistakes
- Overdoing it. Heavy grime on every wall looks unnatural. Concentrate it where it would really appear.
- Uniform weathering. Vary intensity between buildings, and between sides of the same building.
- Hard lines. Blend edges of washes and powders.
- Wrong direction of streaks. Rain stains run downward.
- Weathering before gluing details. Think about whether adhesives and trim will react.
- Ignoring the ground around the building. Add dirt, weeds, gravel and cracked paving at the base so the structure looks planted in its surroundings.
Weathered buildings look best when they are part of a finished scene. See model railroad building plans and structures for sources of kits and plans, city scenery for urban settings, and themed layouts for aged wood in Old West towns. The same techniques work on tunnel portals and, with adjustments, on roads and paving.