Start with the symptom
Before you open a locomotive, work out whether the problem is the loco or the layout. A quick check:
- Try the loco on another piece of track. Put it on a short, clean test loop or a stretch you know is reliable. If it runs, the problem is probably your track or wiring.
- Try a different loco on the same stretch. If another engine stalls at the same spot, the track is the problem.
- Clean the rails and the wheels first. Dirty track and dirty wheels cause most stalling and stuttering. See our guide to cleaning model train track with rubbing alcohol.
Common symptoms and likely causes:
| Symptom | Likely causes |
|---|---|
| Stutters or stops on straight track | Dirty wheels or rails, poor electrical pickup, a dead spot in the track |
| Runs only in one direction | A wiring or decoder fault, or a gear or motor problem |
| Runs, but slowly or noisily | Gunk in the gears, dry gears, or a worn or dirty motor |
| Hums but does not move | Jammed gears, stuck wheels, or a coupler or body part rubbing |
| Derails at the same spot | Track alignment, a too-tight curve or a wheel out of gauge |
Basic cleaning and inspection
- Power off and take the loco off the track.
- Check for obvious obstructions. Hair, fluff and bits of ballast can wrap around axles and gears.
- Clean the wheel treads. One simple approach, described by a trains magazine, is to place a paper towel dampened with isopropyl alcohol across the track, rest the loco with one set of wheels on the towel and the other on the rails, and let the powered wheels spin. Then turn the loco around to clean the other set. For wheels that are not powered, a cotton swab or a microbrush can be used.
- Look at the electrical pickup. Many N scale locos pick up power through wipers or contacts touching the wheels. Bent or dirty contacts can cause trouble.
- Check the couplers and the body. A loose shell or a coupler hanging low can drag or cause derailments.
If you open the shell, take photos as you go. N scale parts are very small, and it is easy to lose or misplace a part.
What a model train test stand is
A test stand lets you run a locomotive without it going anywhere. The most common kind is a roller test stand. The locomotive sits on a cradle or set of rollers, and its wheels spin freely on the rollers. This is useful because:
- You can see whether the loco runs smoothly, in both directions and at different speeds.
- You can break in a new or repaired loco without worrying about derailments.
- You can isolate a problem from the layout. If a loco runs well on the stand and badly on the layout, the track or wiring is the issue.
- You can watch for wheel wobble, a bad gear or a hesitation that is hard to see on a moving train.
Some stands also include a short length of track for testing decoders, programming and sound.
Buying or building a roller test stand
You can buy a roller test stand from model railroad suppliers, and some makers and track brands offer one. Features to look for are rollers that spin freely, a cradle sized for N scale wheels and a way to connect power.
Hobbyists also build their own, and instructions are often shared on model railroad forums. The usual elements are:
- Free-spinning rollers or small bearings in a frame.
- A base that holds the loco level and in place.
- Power leads that connect to the rollers or to track pieces.
Whatever you use, do not let a loco spin freely at full speed for long periods. Bring it up slowly and watch for heat or odd noises.
Lubrication and gearing
Lubrication is a common cause of trouble, and also a risk. Too much oil attracts dirt and can damage plastic parts, and the wrong product may harm gears or paint.
- Use a lubricant sold for model trains and made for plastic gears, and check the label.
- Use very small amounts. A tiny drop is usually enough.
- Keep oil off the wheels and rails, because it will spread and cause stalling.
- If the gears are full of old grease or dirt, clean them gently before applying new lubricant.
If you are not sure which lubricant a particular loco needs, check the manufacturer’s instructions.
DCC and electronics
Many modern N scale locos have a DCC decoder, and some have sound. If you are not sure which yours is, see how to tell if a model train is DCC or DC. A decoder problem can look like a mechanical one. Things to check:
- The loco runs on DC but not on DCC, or the reverse.
- It runs in one direction only.
- The lights flicker or go out.
A decoder can sometimes be reset or reprogrammed. If you suspect a hardware fault, the decoder may need replacing. This is where a repair shop or a skilled friend can help, because small solder joints are easily damaged. The micro-electronics in modern locos are one reason new N scale models cost what they do. See why N scale trains are so expensive.
When to send it for repair
Consider professional help if:
- The loco is valuable or hard to replace.
- It is under warranty. Opening it may affect your warranty, so check first.
- It involves soldering, a decoder replacement or a broken motor.
- You have cleaned and checked the obvious things and it still will not run.
How can I get my Hornby train repaired? Hornby is best known for OO gauge, and its group also owns other brands, including some that make N gauge. The best first step is to check the manufacturer’s website or contact the retailer you bought it from, to see what repair or spare-parts service is currently offered, and whether warranty applies. Local model railway shops and specialist repairers may also take on repairs. Always ask about cost before sending anything.
For other brands, the same approach works. Check the manufacturer’s support page, ask the retailer, or look for a hobby shop or club that handles repairs.
Are N scale trains worth anything?
It depends. The things that tend to affect the value of an N scale item are:
- The maker and the model. Some models are more sought after than others.
- Condition. Working order, intact details and no broken parts matter.
- Original packaging. Items with original boxes and paperwork are generally easier to sell.
- Rarity. Limited runs and discontinued models may be harder to find.
Prices change, so look at recent sold listings for the same item rather than asking prices. Do not assume a used loco is valuable. Many second-hand items sell for less than their original price.
Related reading
- If you are building a layout and want to plan around reliable running, start with N scale track plans.
- Tight curves cause a lot of derailments. See N scale minimum radius.